AR3150P Water Filter Replacement and Reset Instructions (PPC/RO/CTO Filters)
Step 1: Preparation ( In to standby mode)
- Turn off the water inlet valve.
- Open the faucet to release any remaining pressure in the system.
Step 2: Replace the Filter
- Twist and remove the filter (PPC/RO/CTO) that you want to replace.
- Insert the new filter into the machine and twist it into the locked position.
Step 3: Flush the New Filter
- Turn on the water inlet valve.
- Keep the faucet open to flush the new filter.
- Let water run for about 1–3 minutes (approximately 3–5 gallons) to fully flush the system.
Step 4: Filter Reset Function
- Controlled via two touch buttons on the bottom of the control panel:“ Reset ” & “ Select ”
- Touch detection is activated when the user's finger touches the spring panel area and the action is triggered upon release.
- In standby mode:
- Long press the“ Reset ” button to enter reset mode.
- Press “ Select” to cycle through filters; the selected filter’s light will flash white with a breathing effect and a beep will sound.
- Press “ Reset” again to reset the selected filter and exit reset mode.
- To reset another filter, re-enter the reset function.
If no action is taken for 20 seconds, the system will automatically exit reset mode.
AR3150P 淨水器濾芯更換及重置操作說明(PPC / RO / CTO 濾芯)
步驟 1:準備工作(進入待機模式)
- 關閉進水閥門。
- 打開淨水龍頭,釋放系統內殘留的水壓。
- 確認機器已進入待機模式(Standby Mode)。
步驟 2:更換濾芯
- 將需要更換的濾芯(PPC / RO / CTO)旋轉取出。
- 將新濾芯插入機器,按照正確方向旋轉,直到鎖定到位。
步驟 3:沖洗新濾芯
- 打開進水閥門,恢復供水。
- 保持淨水龍頭開啟,沖洗新更換的濾芯。
- 持續放水約 1–3 分鐘(約 3–5 加侖),確保新濾芯及系統內部充分沖洗。
步驟 4:濾芯重置功能(Filter Reset)
- 機器透過控制面板底部的兩個觸控按鈕進行操作:
- Reset(重置)
- Select(選擇)
- 觸控操作方式:
- 當手指接觸控制面板上的彈簧感應區域(Spring Panel Area)時,系統會偵測觸控。
- 放開手指時,系統才會正式執行該操作。
- 重置操作步驟:
- 確認機器處於待機模式(Standby Mode),長按 「Reset」 按鈕,進入濾芯重置模式。
- 按下 「Select」 按鈕,依序切換需要重置的濾芯。
- 被選中的濾芯指示燈會以白色呼吸燈效果閃爍。
- 同時會發出提示音(Beep),表示已選中該濾芯。
- 確認選擇正確的濾芯後,再次按下 「Reset」 按鈕,即可重置該濾芯的使用壽命並退出重置模式。
- 如果需要重置其他濾芯,請重新進入重置功能,重複上述操作。
自動退出功能:
- 如果進入重置模式後,20 秒內沒有任何操作,系統將自動退出重置模式。